egypttent7

How to Replace a Kia Sportage Replacement Key For a variety of Kia models keys, the key has an integrated keyless entry system. The key functions like an remote control and can be exchanged with an Kia dealer. Key fobs can stop working for a variety of reasons, such as the battery of the coin is dead worn buttons or buttons, signal interference, water damage and a faulty receiver module. Here are some suggestions to assist you in getting your Kia key fob that is a replacement for the sportage again. How to replace a remote key or smartkey No matter if your Kia comes with an intelligent key, remote key, push-to-start keys, or regular metal non-transponder key the battery in these keys will eventually require replacement. This is especially the case if your car shows a message that states the remote or smart keys have low battery power. This is a relatively easy process. To replace the battery in the keyfob, remove your mechanical key from the slit on the back of the fob. Then, you need to pry the cover open. Inside the key fob, there will be tiny screws that hold the battery in place. With a small screwdriver, remove the screw and remove the old battery. Then, you can insert the new battery and close the slit on the key fob. Test the key fob by pressing the lock/unlock buttons. It's okay If the doors lock and unlock as expected. You can now use Kia's hands-free lock/unlock function whenever your fingers feel cold or you have to do some errands in Brandon. Note: Certain key fobs (transponder chip or smart keys) may require their programming done. This requires a computer, which is only available to the locksmith for cars or dealer. Other keys (non-transponder metal keys) don't require programming. If your key has to be reprogrammed, you will need to be aware of the number written on the tag of the key code and then record it in a safe place. How do I replace the battery? If the Kia key fob doesn't respond to pressing the lock/unlock button, it is likely that the battery is low. A weak battery can cause other problems like the check engine light turning on or the engine not cranking. Fortunately, replacing the key fob battery is a fairly simple DIY project that requires only the most basic tools. Make sure that you shut off your vehicle and shut all doors prior to beginning. Find the small metal or a plastic piece on the bottom of the key fob. Then, jiggle it until the key pops out. The key can be put into the driver door handle to unlock your car. To replace the battery on the key fob remove the cover on the rear. Utilize a plastic plier tool to loosen up the latch that holds the black negative cable. Remove the old battery and then orient the new one to ensure that the “+” positive side faces your face and the “–” negative side is facing the fob's metal electrical contacts. Push the new CR2032 battery straight into place, avoiding excessive force to avoid damaging or bending the metal contacts. After installing the new battery then turn the key fob off and on in the ignition until the door locks up. You can then test your Kia's keys fob again to confirm that it's working properly. How do you replace a smart key Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The difference between these is that the smart key is equipped with the small blade of a key tucked inside it, while the standard fob isn't equipped with. Both kinds of key fobs contain batteries inside that will eventually need to be replaced. Fortunately, this is quite simple and takes just two minutes. Before you begin, you will want to make sure that you are on a flat surface with enough lighting and that your Kia is off. Remember that the fob is made up of small parts that can be thrown off when you're not careful. The first step is to find the small release button on the back of the lower part of the fob. It's either an oval or circular slot. When you press it, the mechanical key blade will appear and you can then open the key fob. Once you have the key fob open and you are able to remove the old battery, and replace it. The new battery should be a CR-2032 and can be purchased online or at your local auto parts store. After installation with the battery, you should be able to lock or unlock your car with your key fob – even if your engine isn't running! How to replace the mechanical key? The Kia keyfob is an excellent convenience that allows us to lock or unlock our car simply by pressing one button. Like any device like a key fob, the Kia can have issues at times. There are steps that can be taken to fix these issues and ensure that our key fobs are in good condition in the long run. One of the most frequent problems is a low or dead battery. The battery could cause the device to stop working or work intermittently. If this is the case you should replace the battery a new one. If TheKeyLab isn't enough to resolve the problem Try using a standard flat-head screwdriver to break open the casing of the fob's plastic. Be careful not to damage internal components, or scratch the plastic. When the battery is open, carefully take off the old battery and replace it with a brand new one. When the new battery is in, close and open the doors using the mechanical key (every kia fob has an emergency mechanical key that can fit in the slot). Test the key fob to ensure it's functioning correctly. Contact a dealer locksmith to solve the issue in the event that the fob is not working. To avoid a lockout in the future ensure you have an emergency key that can work on all trunk and door cylinders.